Solar Panel Frame Roll Forming Machine (Carbon Steel Type)

Deskripsi Produk

 

Solar Panel Frame Roll Forming Machine (Carbon Steel Type)

---

1. Introduction

This roll forming line is engineered for manufacturing carbon steel frames used in photovoltaic (PV) solar panels. Designed for stability and efficiency, the machine automates punching, forming, and cutting in a continuous process, allowing for high-precision frame production with minimal material waste.

This model is optimized for long-run production with programmable control and real-time diagnostics.

---

2. Machine Composition

The system is composed of the following modules:

1. Manual Decoiler or Hydraulic Uncoiler

2. Feeding and Leveling System

3. Precision Servo Punching Station

4. Main Roll Forming Section

5. Servo Flying Shear Cut-Off Unit

6. Runout Table and Optional Auto Stacker

7. Centralized Electrical Control System (PLC + HMI)

8. 

---

3. Technical Data

Parameter	Specification
Frame Material	Cold rolled carbon steel, galvanized steel
Material Width	45 – 100 mm
Material Thickness	0.8 – 2.0 mm
Production Speed	Up to 15 meters per minute
Forming Stations	14 – 20 steps (customizable)
Cutting Tolerance	±0.3 mm
Punching Accuracy	±0.5 mm
Control System	Siemens PLC, touch HMI, encoder feedback
Required Power Supply	380V, 50Hz, 3-phase

---

4. Operating Procedure

▶️ Before You Start

• Check power connection, oil level in hydraulic system, and air pressure.

• Ensure the punching mold and cutting blade are clean and firmly secured.

• Load the steel coil on the uncoiler and lock with safety clamps.

---

▶️ Startup Process

1. System Boot

   • Switch on the main power.

   • Wait for the control panel to complete system diagnostics.

2. Parameter Input via HMI

   • Input length of frame, punching positions, and number of holes.

   • Set the batch quantity and material thickness.

   • Load or recall saved profile data if applicable.

3. Material Feeding

   • Jog feed the material to align with the punching station.

   • Use the “manual run” mode to test one cycle before full run.

4. Production Mode

   • Switch to “Auto Run”.

   • Monitor the HMI screen for live speed, punch counts, and cut count.

   • Inspect first 2–3 frames for dimensional accuracy.

---

▶️ Stopping & Changeover

• Press “Stop” and wait for the current piece to finish cutting.

• Change punching dies or adjust rollers if switching frame types.

• Use jog mode to test feed before resuming auto production.

---

5. Routine Maintenance

Task	Frequency	Notes
Clean roll surfaces	Daily	Use anti-rust oil
Check punching die wear	Weekly	Replace if edge dull
Lubricate forming bearings	Every 2 days	Use light-grade machine oil
Inspect sensors & cables	Weekly	Check for wear or disconnection
Back up PLC data	Monthly	Via USB port on HMI

 

---

6. Troubleshooting Guide

Symptom	Possible Cause	Solution
Frame length deviation	Encoder loose / wrong data	Recalibrate encoder
Punch misalignment	Servo lag or mold shift	Reposition mold and reset zero
Uneven frame shape	Roller misadjusted	Re-level forming station
Material jam in cutter	Blade worn or too slow	Replace blade, adjust servo timing

 

---

7. Frequently Asked Questions (FAQ)

Q: Is carbon steel strong enough for outdoor frames?
A: Yes. With proper galvanization or powder coating, carbon steel frames offer excellent strength and corrosion resistance at a much lower cost than aluminum.

Q: Can one machine make different sizes?
A: Absolutely. Frame length, hole positions, and even roll gaps can be adjusted via PLC. Some wider profiles may need partial tool change.

Q: What is the estimated tool life?
A: Punching dies typically last 80,000–120,000 cycles depending on material. Cutting blades may last 30,000–50,000 cuts with proper lubrication.

Q: Can I integrate a stacker later?
A: Yes. The output section includes optional ports and logic for integration with auto stackers or robotic arms.

---

8. Safety Instructions

• Never place hands near the roll station during operation.

• Always disconnect power before adjusting tooling.

• Emergency stops are located at the entry and exit ends.

• Wear gloves and safety glasses when changing dies.

Strip pada profil ini secara bertahap berubah menuju bentuk akhirnya. Proses ini mematuhi tekanan mekanis dan karakteristik logam serta memungkinkan penggunaan berbagai tingkatan baja. Dua poros horizontal pada setiap kepala dikontrol oleh motor mesin, yang memastikan penggerak strip secara teratur. Selama proses pembentukan gulungan dingin, operasi seperti melubangi, mencap logo, dapat dilakukan secara daring.
Kemudian, bagian logam akhir dipotong oleh mesin pemotong servo hidrolik sesuai panjang yang diinginkan.

1.Apa kegunaan mesin roll forming?

Mesin cold roll forming digunakan dalam berbagai industri, termasuk konstruksi, otomotif, kedirgantaraan, dan manufaktur. Mesin ini sangat otomatis dan dapat menghasilkan produk berkualitas tinggi dengan kecepatan tinggi, sehingga menjadi pilihan populer untuk produksi massal.

4. Aliran teknis jalur produksi

{Steel Tape}→ Uncoiler →Strip-head Cutter and welder→Spiral accumulator→Forming section →Hole punching device→Hydraulic servo driven cutoff→→ Run-out table

PERALATAN HUBUNGAN

Kami menyediakan semua peralatan untuk bagian masuk pabrik tabung:

Mobil Koil

Pembuka Kepala Tunggal dan Ganda, Pembuka Kepala Hidrolik dan Pneumatik

Pengupas dan tahan lengan gulung

Mesin Perata

Mesin Pemotong dan Las Ujung Otomatis dan Semi Otomatis

Vertical Cage Accumulator​ & Horizontal Loop Accumulator & Landing Horizontal Spiral Loop Accumulator

BAGIAN FINISHING TUBE MILL

We provides all equipment to tube mill Finishing section:

1. Eddy current machine

2. Seam annealing machine

3. Straightener machine

4. Chamfer and end facer machine

5. Hydro Tester machine

6. Threading machine

7. Painting and oil machine

8. Automatic bundle and package machine

9. Drilling machine

SUKU CADANG UNTUK DIPILIH

Suku Cadang Kami Berlaku:

1. Roller, Mould, Cr12, Cr12Mov material, D2,D3 material

2. Ferrite, Impeder, Fiberglass tube

3. HSS saw blades, TCT Saw blades, Friction saw blades

4. OD burr remove inserts, ID burr remover inserts

5. HF welder Induction Coil and other HF welder spare parts

6. Copper tube for induction Coil, PTFE pipe for Induction Coil

7. Mosfet, Boards

8. Steel pipe Strapping machine

9. Zinc Spray Machine, Zinc wire, Zinc spray gun

SERTIFIKAT KAMI

LAYANAN KAMI

Mengapa Memilih Kami?

Teknologi Terkemuka, Kualitas Andal, Layanan Luar Biasa!

Desain yang dioptimalkan, Pilihan material berkualitas tinggi! 

Jaminan proses perlakuan panas!

Roda gigi spiral bevel, kopling roda gigi drum dan karburisasi.

Pendinginan gigi roda gigi.

Sistem penggerak stabil, efisien, dan dapat dipakai dengan tingkat kebisingan lebih rendah.

Ketahanan aus dengan presisi tinggi dan umur rol yang panjang.

Semua mesin Bubut, Alur Kunci diposisikan dan digiling oleh CNC.

Layanan Kami

Layanan pra-penjualan

1.  We can provide machine running videos for reference

2.  We will recommend the most suitable equipment according to the needs of customers

3.  We can provide the layout of the factory

4.  We welcome customers to visit our factory 

Layanan purna jual

1. Kami akan mengirimkan mesin dan memberikan dokumen tepat waktu untuk memastikan Anda bisa mendapatkan mesin dengan cepat

2. Setelah Anda menyelesaikan kondisi Persiapan, tim teknisi layanan purna jual kami yang cepat dan profesional akan pergi ke pabrik Anda untuk memasang mesin, memberi Anda manual pengoperasian, dan melatih karyawan Anda hingga mereka dapat mengoperasikan mesin dengan baik.

3. Kami menyediakan garansi satu tahun dan dukungan teknis seumur hidup.

4. Staf yang terlatih & berpengalaman akan menjawab semua pertanyaan Anda dalam bahasa Inggris dan Mandarin

5,24 jam untuk respon teknisi.

6.Hubungan bisnis Anda dengan kami akan dirahasiakan dari pihak ketiga mana pun.

Kontrol Kualitas

Kami memiliki departemen kualitas tunggal, yang memastikan bahan bakunya bagus, dan memastikan mesin berjalan lancar.